Full Width [alt+shift+f] Shortcuts [alt+shift+k]
Sign Up [alt+shift+s] Log In [alt+shift+l]
46

Dual Booting OpenBSD and Alpine Linux on a X220 ThinkPad

from bt RSS Feed [alt+shift+b] in programming

Dual Booting OpenBSD and Alpine Linux on a X220 ThinkPad 2024-07-10 I’ve always found it useful to run both OpenBSD and some form of Linux variation on my personal machines. Most times, I would default to running one OS on bare metal, while the other would simply live in a VM. This works okay but I prefer my operating systems having a “hardware separator” - if that makes sense? So, I set off to start dual booting both OpenBSD and Alpine Linux on my X220 ThinkPad. I should mention that I planned to write this blog post a couple weeks ago, but the original Dogfish mSATA SSD I ordered wasn’t compatible with my X220 (even though they say it is supported…). Luckily, I found a replacement drive in one of my “computer parts” drawer. Hoarding tech always prevails! The original Dogfish mSATA slotted in the X220. Too bad it didn't work... I came across my old Raspberry Pi 400, which I previously wrote about when stuffing an SSD inside it, and proceeded to gut the drive. It’s a cheap KingSpec SSD with a whopping 64GB of storage space. But that didn’t matter since the plan was to install the wonderfully small Alpine Linux. 64 GB would be plenty of space for us! Getting Started I already had the Alpine Linux ISO installed on a random thumb drive, so that made things quicker right off the bat. The next step was opening up my X220 and slotting in the very tiny mSATA. This introduced the first minor issue: the drive was too small. I could have looked into something more “professional-looking” in order to seat the drive properly but I decided to stick with electrical tape. Get it?… After applying the tape I closed the machine back up. The KingSpec mSATA slotted in the X220 and secured with top-of-the-line electrical tape... Installing Alpine Linux Next, I needed to tell the BIOS to boot into my thumb drive containing the Alpine ISO. Once the proper order was set, I rebooted the machine and ran through the standard Alpine installer. No problems to report there. My X220 booting...
10th Jul 2024

Stay updated

Get a weekly newsletter with the top 5 articles worth reading every week.

More from bt RSS Feed

Installing OpenBSD on Linveo KVM VPS

Installing OpenBSD on Linveo KVM VPS 2024-10-21 I recently came across an amazing deal for a VPS on Linveo. For just $15 a year they provide: AMD KVM 1GB 1024 MB RAM 1 CPU Core 25 GB NVMe SSD 2000 GB Bandwidth It’s a pretty great deal and I suggest you look more into it if you’re interested! But this post is more focused on setting up OpenBSD via the custom ISO option in the KVM dashboard. Linveo already provides several Linux OS options, along with FreeBSD by default (which is great!). Since there is no OpenBSD template we need to do things manually. Getting Started Once you have your initial VPS up and running, login to the main dashboard and navigate to the Media tab. Under CD/DVD-ROM you’ll want to click “Custom CD/DVD” and enter the direct link to the install76.iso: https://cdn.openbsd.org/pub/OpenBSD/7.6/amd64/install76.iso The "Media" tab of the Linveo Dashboard. Use the official ISO link and set the Boot Order to CD/DVD. Select “Insert”, then set your Boot Order to CD/DVD and click “Apply”. Once complete, Restart your server. Installing via VNC With the server rebooting, jump over to Options and click on “Browser VNC” to launch the web-based VNC client. From here we will boot into the OpenBSD installer and get things going! Follow the installer as you normally would when installing OpenBSD (if you’re unsure, I have a step-by-step walkthrough) until you reach the IPv4 selection. At this point you will want to input your servers IPv4 and IPv6 IPs found under your Network section of your dashboard. Next you will want to set the IPv6 route to first default listed option (not “none”). After that is complete, choose cd0 for your install media (don’t worry about http yet). Continue with the rest of the install (make users if desired, etc) until it tells you to reboot the machine. Go back to the Linveo Dashboard, switch your Boot Order back to “Harddrive” and reboot the machine directly. Booting into OpenBSD Load into the VNC client again. If you did everything correctly you should be greeted with the OpenBSD login prompt. There are a few tweaks we still need to make, so login as the root user. Remember how we installed our sets directly from the cd0? We’ll want to change that. Since we are running OpenBSD “virtually” through KVM, our target network interface will be vio0. Edit the /etc/hostname.vio0 file and add the following: dhcp !route add default <your_gateway_ip> The <your_gateway_ip> can be found under the Network tab of your dashboard. The next file we need to tweak is /etc/resolv.conf. Add the following to it: nameserver 8.8.8.8 nameserver 1.1.1.1 These nameservers are based on your selected IPs under the Resolvers section of Network in the Linveo dashboard. Change these as you see fit, so long as they match what you place in the resolve.conf file. Finally, the last file we need to edit is /etc/pf.conf. Like the others, add the following: pass out proto { tcp, udp } from any to any port 53 Final Stretch Now just reboot the server. Log back in as your desired user and everything should be working as expected! You can perform a simple test to check: ping openbsd.org This should work - meaning your network is up and running! Now you’re free to enjoy the beauty that is OpenBSD.

21st Oct 2024 • 96 votes
Burning & Playing PS2 Games without a Modded Console

Burning & Playing PS2 Games without a Modded Console 2024-09-02 Important: I do not support pirating or obtaining illegal copies of video games. This process should only be used to copy your existing PS2 games for backup, in case of accidental damage to the original disc. Requirements Note: This tutorial is tailored towards macOS users, but most things should work similar on Windows or Linux. You will need: An official PS2 game disc (the one you wish to copy) A PS2 Slim console An Apple device with a optical DVD drive (or a portable USB DVD drive) Some time and a coffee! (or tea) Create an ISO Image of Your PS2 Disc: Insert your PS2 disc into your optical drive. Open Disk Utility (Applications > Utilities) In Disk Utility, select your PS2 disc from the sidebar Click on the File menu, then select New Image > Image from [Disc Name] Choose a destination to save the ISO file and select the format as DVD/CD Master Name your file and click Save. Disk Utility will create a .cdr file, which is essentially an ISO file Before we move on, we will need to convert that newly created cdr file into ISO. Navigate to the directory where the .cdr file is located and use the hdiutil command to convert the .cdr file to an ISO file: hdiutil convert yourfile.cdr -format UDTO -o yourfile.iso You’ll end up with a file named yourfile.iso.cdr. Rename it by removing the .cdr extension to make it an .iso file: mv yourfile.iso.cdr yourfile.iso Done and done. Getting Started For Mac and Linux users, you will need to install Wine in order to run the patcher: # macOS brew install wine-stable # Linux (Debian) apt install wine Clone & Run the Patcher Clone the FreeDVDBoot ESR Patcher: git clone https://git.sr.ht/~bt/fdvdb-esr Navigate to the cloned project folder: cd /path/to/fdvdb-esr The run the executable: wine FDVDB_ESR_Patcher.exe Now you need to select your previously cloned ISO file, use the default Payload setting and then click Patch!. After a few seconds your file should be patched. Burning Our ISO to DVD It’s time for the main event! Insert a blank DVD-R into your disc drive and mount it. Then right click on your patched ISO file and run “Burn Disk Image to Disc...". From here, you want to make sure you select the slowest write speed and enable verification. Once the file is written to the disc and verified (verification might fail - it is safe to ignore) you can remove the disc from the drive. Before Playing the Game Make sure you change the PS2 disc speed from Standard to Fast in the main “Browser” setting before you put the game into your console. After that, enjoy playing your cloned PS2 game!

2nd Sep 2024 • 96 votes
Perspective

Perspective 2024-08-06 I recently read both Starting Hospice and No Salt posted on Jake’s blog and was quite moved. I don’t know Jake and have never met him - but his writing and shared experiences give a very real look into his mind and perspective. If you haven’t yet, I strongly recommend giving his site a read (or at the very least those two posts). It made me reflect on my own life, shift my perspective and realize how fortunate I truly am. Losing Focus I think we all find ourselves losing focus on the truly important things in life. That’s normal and expected. Maybe your house needs repairs, or you’re crunching for an upcoming deadline, or your prepping for a long a work trip, or your stressed out hunting for a job. Whatever it might be, our brains are very good at getting derailed and putting all our attention into less important things. But I believe our minds need to wander and focus on the less important. Otherwise your mental health would suffer greatly. And I should note, some of these “stresses” still require our attention. I just don’t think they should consume us. I’m not advocating that we need to constantly be obsessing over the limited time we have on this spinning rock, or that we should smother our families with over-the-top love. Just stopping and reflecting on these things can really put any worries you have into perspective. It might be cliche to state the obvious, “Be grateful for what you have!” but cliche or not - it’s true. Jake will be leaving behind not just his friends and family, but also his wife who is 7-months pregnant. I can’t begin to imagine the range of emotions everyone close to him must be feeling. I know I would be furious, which doesn’t make sense since something like this is so far removed from human control. Being angry would just be wasted energy. But that’s easier said than done. I don’t have a whole lot else to say on the matter. This post also pales in comparison to Jake’s actual experience and shared perspective on his site. I really wasn’t even sure to share this on my site, in fear that I would be somehow disrespecting Jake’s memory (along with his much better writing skills and openness). But then I thought, if anything, I could help reach Jake’s story to even one other person and help them reflect on their own perspective as well. Now if you’ll excuse me, I’m going to take a long, purposefully slow walk with my family.

6th Aug 2024 • 47 votes
Building rbenv on OpenBSD 7.5

Building rbenv on OpenBSD 7.5 2024-06-02 I use Ruby (specifically with Jekyll) for a lot of my clubs/projects while using my personal laptop (X220 ThinkPad) which is runs OpenBSD. Since I recently upgraded to OpenBSD 7.5 I thought it could be helpful for others if I shared my process of building and using rbenv to install different Ruby versions. Before We Build First, be sure to install the required packages in order to build from source, and then clone the core rbenv repo: pkg_add git gcc gmake libffi libyaml openssl git clone https://github.com/rbenv/rbenv.git ~/.rbenv Building rbenv Add rbenv to your PATH and initialize it (place this inside your .bashrc or .zshrc etc): export PATH="$HOME/.rbenv/bin:$PATH" export PATH="$HOME/.rbenv/shims:$PATH" export RUBY_CONFIGURE_OPTS="--with-openssl-dir=/usr/local" eval "$(rbenv init -)" Then reload your shell (zsh in this example): source ~/.zshrc Next we will need to install ruby-build as a rbenv plugin. Clone the ruby-build repository into the rbenv plugins directory: git clone https://github.com/rbenv/ruby-build.git ~/.rbenv/plugins/ruby-build Installing Ruby and Setting Our Version Now use rbenv to install the desired version of Ruby (we will get an older version for this example): rbenv install 3.3.0 If you run into issues, you may need to specify your openssl directory: RUBY_CONFIGURE_OPTS="--with-openssl-dir=/usr/local" rbenv install 3.3.0 If you’re on a slower machine (like mine) this might take a little bit. Just grab a coffee or a snack while you wait! Then navigate to your project of choice and set the local Ruby version: rbenv local 3.3.0 That’s it! If you’d prefer to set this version of Ruby for all projects going forward, simply replace local with global.

2nd Jun 2024 • 35 votes

More in programming

Modifications to add a booty to Loops by Kat's Ditto amigurumi

I found a wonderful free crochet pattern for the Pokémon Ditto from Loops by Kat, but I decided I wanted to make a version with more than 3 "leg" blobs like the original pattern had. Specifically, I wanted to add two more smaller blobs in the back to help stabilize Ditto when they're sitting and also add a butt to our favorite transforming blob. Hazel Knits Cadence, a worsted weight superwash merino, in Terrywinkle that I had in my stash (I used about a third of the skein/36 grams/66 yards/60 meters), and I crocheted with a 2.5 mm hook. I make very tightly stitched amigurumi - do whatever is a good fit for you and your yarn! I used two 6 mm round safety eyes, and I embroidered the mouth with scraps of Hazelknits Cadence in Coral, Bloom, and Signature Black. The above photo is more true to color than some of the ones I took where Ditto looks more pink. I made Ditto's 2 additional booty blobs intentionally off-center by embracing the natural lean of crochet stitches - this gives a more animated or "in motion" feel to Ditto. As an added bonus, this simplifies the pattern as everyone's tension will be a little different, and thus everyone's off-centering a little delightfully different, too, but centering it instead wouldn't be the same for everyone! Here's all the information to modify Kat's crochet pattern to create a 5-blobbed Ditto. I use US crochet terminology. This pattern modification is also available as a pdf. Follow Kat's pattern through round 13. At round 14, it's time to start modifying to add the space and shaping for the additional blobs. There are also 3 more rows in this section to better fit the new 5-blob proportions. Modified increases in body, beginning at round 14 (with additional rounds, too): Round 14: 3 sc, 1 inc, 46 sc, 1 inc, 3 sc (56) Round 15: 56 sc (56) Round 16: 2 sc, 1 inc, 2 sc, 1 inc, 44 sc, 1 inc, 2 sc, 1 inc, 2 sc (60) Round 17: 60 sc (60) Round 18: inc, 4 sc, inc, 48 sc, inc, 5 sc (63) Round 19: 63 sc (63) Round 20: dec (through front loop of first stitch and both loops of second stitch), inc, 9 sc, inc, 38 sc, inc, 11 sc (65) At this point, the original pattern suggests placing the safety eyes, but I think it makes more sense to do this after you've made the "butt" and divided the stitches the 3 main "front" "leg" blobs from the original pattern. You'll still have plenty of access to place them then. Roadmap for doing 5 "leg" blobs instead of 3 To make 5 blobs, you use some of the main body's stitches and some created stitches for each. Created stitches are a combination of chains, pickups on the back of chains, pickups in the connections between the chains and the main body, and pickups in the connections between the chains. The "butt" "leg"/mounds are created before the 3 original "legs," and the left "butt" "leg"/mound is made before the right one. 1. Left "butt" "leg"/mound: This is the left "butt" cheek when viewed from the bottom. (While this is really the right butt cheek from Ditto's perspective, I'm calling it left because we're crocheting while viewing from below so it's backwards.) The start of round is the same as the start of round from making the body of the blob, so you can continue as usual. Round 1: 13 sc, chain 11 (24) Round 2: connect chain at previous start of round (skipping 52 stitches) then 24 sc (24) Round 3: (6 sc, dec) x 3 (21) Round 4: (2 sc, dec, 3 sc) x 3 (18) Round 5: (sc, dec) x 6 (12) Round 6: 6 dec (6) Finish off by looping through front loops of all 6 stitches and pull tight, etc. 2. Right "butt" "leg"/mound: This is the right "butt" cheek when viewed from the bottom. The start of round for this "butt" "leg" is 12 stitches before the body/left "butt" leg start of round. This is the second stitch in an increase from the last round of the body. Round 1: 12 sc, 1 dec in the corner of body connected to first "butt" "leg" (pictured below), 4 sc in the bottom loops in the existing chain, chain 7 (24) Round 2: connect chain at start of round for this "butt" "leg" (skipping other blob's additional 7 chains and 40 stitches in the main body) then 24 sc (24) Round 3: (6 sc, dec) x 3 (21) Round 4: (2 sc, dec, 3 sc) x 3 (18) Round 5: (sc, dec) x 6 (12) Round 6: 6 dec (6) Finish off by looping through front loops of all 6 stitches and pull tight, etc. Getting back to the original pattern for the 3 main "legs": After both "butt" "legs"/mounds are done, there are 40 stitches on the original body, 7 chain stitches that can be picked up from each "butt" leg" that haven't been picked up in a second location, which totals the original 54 stitches - this sets you up for the 3 blobs as described in the original pattern. Between each "butt" "leg" and the main body and between the two "butt" "legs" themselves are an additional 3 connections that are also picked up and decreased appropriately to keep the seams between "legs" tight. As a reminder, here's the road map, which shows how to divide up these stitches for the Ditto's main three "legs:" You might find it helpful to visualize this division by temporarily stringing up some scrap yarn to preview the divisions: If you'd like, place stitch markers like I did to delineate the division: Now that you've visualized how you're dividing the main "leg" blobs, it's a good time to place safety eyes if you're using safety eyes for eyes. I placed mine between rows 7 and 8 counted down from the small head blob and left 8 stitches between the eyes. Now you can proceed to make the main legs in the same order as the original pattern. 3. Main "leg" blob 1: This is the left "leg" blob labeled 1 in the original pattern. To start, connect your yarn into the first stitch in the main body after where the main body meets the left "butt" mound. Round 1: 18 sc, chain 9, 1 sc in the 2nd bottom loop in the chain right of the body/left "butt" mound connection, dec through the leftmost bottom loop in the chain on the left "butt" mound and the loop on top of the meeting of the main body/left "butt" mound (pictured below). (29) In the start of the original pattern "leg" 1, here are the two loops in the decrease through the left most chain loop on the left "butt" mound and the loop on top of the meeting of the main body/left "butt" mound. Follow the original pattern's Rounds 19 to 23 and finish off blob "leg" 1 as written. 4. Main "leg" blob 2: This is the right "leg" blob labeled 2 in the original pattern. To start, connect your yarn into 15th stitch from where the main body meets the right "butt" mound - there should be 7 skipped stitches along the front of the Ditto between this start of round and the left "leg" blob's last stitch on the front side of Ditto before the chaining. Round 1: 15 sc, dec through the loop on top of the meeting of the main body/right "butt" mound and the rightmost bottom loop in the chain on the right "butt" mound (pictured below), 4 sc in the bottom loops in the chain on the right "butt" mound, chain 9 (29) In the start of the original pattern "leg" 2, here are the two loops in the decrease through the loop on top of the meeting of the main body/right "butt" mound and the rightmost chain loop on the right "butt" mound. Connect chain at start of round for this blob "leg" at the beginning of round 2's first sc and continue the original pattern's Rounds 2 to 6 for blob "leg" 2 as written. As in the original pattern, now is a good time to stuff your Ditto most of the way! 5. Main "leg" blob 3: This is the center "leg" blob labeled 3 in the original pattern. Round 1: Start in the corner next to left "leg" 1 on the front side (pictured below). 37 sc into the following stitches you pick up: 7 stitches along the main body 1 stitch in the corner of the main body and right "leg" 2 9 stitches in the bottom loops of the chain along right "leg" 2 1 stitch in the corner of right "leg" 2 and the right "butt" mound 2 stitches in the bottom loops of the chain along the right "butt" mound 1 stitch in the corner between the two "butt" mounds 5 stitches in the bottom loops of the chain along the left "butt" mound 1 stitch in the corner of the left "butt" mound and left "leg" 1 9 stitches in the bottom loops of the chain along left "leg" 1 1 stitch in the corner of left "leg" 1 and the main body (37) My lime green running stitch marker indicates the start of round pickup location for making the main blob "leg" 3. To compensate for the extra 5 stitches from those corners, I decreased in the second round at the corresponding locations instead of just single crocheting the whole way around to ensure the end of my round 2 of this section had the specified 32 stitches: Round 2: 6 sc, dec, 8 sc, dec, sc, dec, 4 sc, dec, 8 sc, dec (32) After round 2, I continued with the rest of the original pattern to finish the middle blob "leg" 3. Make the two arms according to the original pattern. I attached them less symmetrically than the original suggested. Finally, embroider a mouth for Ditto. You can either do this in black to match the safety eyes or create a two-toned mouth in red and pink to make a very happy looking Ditto like I did. FYI, this is also documented as a project on Ravelry (though it's a lot harder to follow since photos couldn't be inline).

6 hours ago • 1 votes
Tyding up my side projects

Being focused is about doing less things, and giving more space to the stuff that matters. I am spread out on too many projects and I can’t give enough attention to all of them. It’s time to clearly sort out which one I will keep maintaining and which I should drop entirely. Chuttersnap Mikochi Mikochi is a self-hostable remote file manager I’ve started in 2023. It’s my most successful open source project. I personally use it every day, and thousands of people have adopted it and started using it on their own servers. This year the project has been receiving more and more attention. Maybe it just reached a critical mass of users. In practice, that means a bit more maintenance work, since people have been pointing out bugs and suggesting new features. At the same time, working on Mikochi is fairly enjoyable. It’s a small, self-contained project made with technologies I enjoy working with. I’ve got no complaints about spending some time working on it. Verdict: Keep maintaining Mikochi and actively continue improving it. Itako Itako is an investment portfolio tracking SaaS. I built it for the most part between 2023 and 2025. In terms of scope, it’s the largest project I’ve done entirely by myself. Is it a success? Not really. There are definitely a lot of people who tried Itako, and some who’ve kept using it a bit. But it’s not engaging enough for anyone to consider getting the premium plan. And honestly I don’t find myself using it that much. My view of investing and portfolio management has significantly shifted since I started this project. While I used to think that more sophisticated analysis would lead to better returns, I now realize that the only strategies that consistently make money are honestly stupidly simple. Or maybe it’s a U curve: on one end you’ve got a monkey throwing darts, on the other end you’ve got Jane Street, and everyone in-between fails to beat the market. Anyway, the biggest issue with Itako is how dull working on it is. The interesting parts of the projects are working on statistics and data visualization. But in practice, 90% of the time is spent tediously fixing data, understanding why some German stocks have an exchange labelled XETRA instead of XETR, why some Belgian stocks still have quotes while Euronext shows them as delisted… Verdict: Shut down Itako today. Milou Milou is static site generator for press kits. It started as a fork of presskit.html which was completely abandoned at the time. It’s a very useful tool. At Tsukumogami, it’s part of our Cloudflare pipeline which builds our website in a few minutes whenever we need to change something. It seems like a few other game studios have picked it up, although I rarely get any feedback about it. I’ve not spent too much time working on it in 2026. I think it could be interesting to come back to it and add a feature or two. Better support for multiple languages could be an idea. At least, I need to make sure we don’t fall into the good old Node.js dependency rot. Verdict: Spend some time on Milou. Luluka Earlier this year, I created Luluka. It’s a CLI that allows previewing the output of Ebitengine shaders. I do still think Ebitengine is a great engine and Go is better suited for game development than most people realize. However, after quite a long period of experimentation around it, we’ve decided to remain a Godot studio. On top of having quite a large sunk cost in infrastructure surrounding Godot, the tooling and possibility of doing 3D games still makes it a more attractive engine for our use cases. And I’ve been doing a lot of 3D work lately, so better put those hours to use. Verdict: Archive the project. The rest I’ve had a lot of good ideas that stayed as almost empty repositories in my GitHub. For example, Hakumei was a terminal companion to Mikochi. I made a few commits on this project and never found the time to work on it again. I have to admit I’m probably never going to have the time to work on all those repositories. Time to archive them all!

3 days ago • 1 votes
The Pulse: Details of incident.io’s AI spend

The resiliency startup has slashed the amount it spends on AI; down from $4,500 per dev, per month, in August, to $1,600 now.

4 days ago • 1 votes
First Strike

Internalize this graph, we post it on this blog a lot. If trends continue, China will have 10x the electricity of the US in 10 years. Whenever you think about geopolitical strategy, always keep it in mind, because whatever your plans are must consider this. Here’s a strategy that would make sense for America long term. Sell as many AI chips into China as possible, use the money to purchase solar panel and battery factories, and build out electricity capacity as quickly as possible. Fundamentally, compute is a function of electricity. That’s the sort of long term thinking that gives America a chance. With robotic labor, immigrants like Jensen and Elon, a business friendly culture, and an incredible chunk of land, it’s not so clear who is ahead in 50 years. Regardless, I do know this strategy would lead to massive prosperity for the citizens of both countries. However, that’s not close to what we see happening. We see a lot of short term zero sum thinking in action. It’s very scary what the US “AI race” mentality leads to. When exactly does the race end? Whatever capabilities you have today will eventually be matched, unless… …you believe that you can use ASI in a decapitating first strike. I’m worried that this is what these people see as the only way out. It probably doesn’t work, can you outthink steel and drone production? I don’t see how, see my critiques here. But I’m not totally sure, I’m not a superintelligence. And if it does work, that may be the end. My likelihood of imminent WWIII went up a lot with the nationalization of NVIDIA.

4 days ago • 1 votes
Not everybody is an AI expert - and that’s fine

This post was previously published through my newsletter on November 9, 2026. From time to time, I will republish newsletter issues on my blog here if I think people (and search engines) might benefit from it. If you want to read everything I’ve written once it is posted, I recommend signing up for the newsletter. If you’re doing anything to stay on top of what is happening in the world of software testing and test automation, like browsing or even posting on LinkedIn, which I stopped doing for the foreseeable future, or reading blog posts - my preferred way of keeping up these days, and I highly recommend Dawid Dylowicz’s excellent Software Testing Weekly aggregator mailing list if you prefer longer-form reading, too you’d be thinking that AI has consumed our entire field, and that everybody (or at least those who post or write in public) is an AI expert these days. The reality, though, is far from that. Yes, some people use a lot of AI, even when I would only call a small fraction of them ‘experts’. I definitely do not classify myself as an ‘AI expert’, by the way. A much larger group uses AI on a less frequent basis, and they’re getting some value out of it. Sometimes more, sometimes less. That’s the group I’m probably in. And then there’s a group of people who haven’t really been using a lot of AI at all so far, beyond maybe the odd prompt to ChatGPT or Claude. I don’t have the actual numbers, but I suspect that this group is a lot larger than you would think from browsing your feed or surfing the blogosphere. You just don’t see them, because they’re typically not the people who do a lot of work in public. A few weeks ago, I started working with a small group of testers to teach them how to use AI in their daily work. This work covers both test automation as well as broader software testing tasks, as some of them contribute to automation on a daily basis, but not all of them do. I’m working with them one day per week, on average, for three months, and we’re making small steps towards making AI a more prominent tool in their tool belt. So, what are we working on right now? I’m pulling ideas from my ‘Valuable Feedback, Fast with AI’ course, and so far, we’ve spent some time setting up Claude, going over some important concepts such as context windows, models, tokens, and (of course!) the probabilistic nature of LLMs, and what that means for the results they provide. We have gone through several initial conversations, using Claude to learn more about and review specific user stories, which was an excellent segue into using talking about MCPs and setting up a connection to both Jira and Confluence using the Atlassian MCP. Last week, we also started experimenting with writing straightforward skills to make it easier for Claude to repeat certain actions in a structured way. These actions ranged from reviewing stories and acceptance criteria to refactoring small chunks of code in their (Robot Framework-based) test automation suite. What I loved about this is the avalanche of ideas that popped up in their heads when they saw how easy it was to use Claude. We made a short to-do list of ideas to try out for the next couple of weeks, and I’m looking forward to seeing them getting more confident around using Claude. One thing I have noticed is that their level of comfort around using AI varies quite a bit. Some of them are naturally quite cautious, which means they’ll ask ‘can we really do this?’ and ‘should we really do this?’ frequently before even submitting a single prompt. This is a good habit, I think, but we’ll have to do some work to get them more comfortable with using LLMs, without losing too much of that caution. Others in the group are the opposite: I need to hold them back a little, because otherwise they’ll create a beautiful mess within days, simply because they see so many opportunities to use Claude in their work. That, too, isn’t inherently bad, but I do want to teach them not just how to get the most out of an LLM, but also (more so) how to use AI prudently. Over the next couple of months, we’ll dive deeper into writing better prompts, creating and structuring skills, better context management, and creating and using agents, and probably a few more things, too. I’m looking forward to seeing these people grow more comfortable around using AI in their daily work, and figuring out where AI genuinely adds value and where it doesn’t in their own context. Is there a deeper message in this newsletter? Maybe not, and I’m just happy to tell you about this project, and how it is a great example of a what I call ‘corporate mentoring’, a very efficient way of teaching a small group of engineers new skills, within their own context. But maybe it’s also to show you that, despite what you might see on the Internet, especially those places featuring a lot of self-congratulation (I’m looking at you, LinkedIn), not everybody out there is an AI expert. At least not yet. So, if you feel like you’re ‘behind’ simply because you’re not running at least 17 agents continuously, creating 5400 merge requests per day, know that you’re not alone. Quite far from it, I would say.

4 days ago • 1 votes
📚 BoredReading

You seem to be enjoying this.

Join free to unlock everything.

Create free account

Already have an account? Sign in