This Refurb Weekend is a sequel in two ways. Six years ago I fixed the power supply and case fan in my 68EC030-based Alpha Microsystems Eagle 300, a more modernized and substantially faster Alpha Micro running AMOS, their unique DEC-inspired multiuser operating system. These blue-collar boxes were very common in many vertical markets due to their tightly integrated business-specific software packages, and are especially unusual for running their big-endian 68000-series processors little-endian (for data file backwards compatibility with their WD-16 ancestors). The 1990s-era Alpha Micro Eagle family improves on the originals with later 68K and even ColdFire CPUs, plus Ethernet and faster SCSI. The second way it's a sequel is to our previous Alpha Micro refurb weekend, a double header restoring an Alpha Micro AM-1000 and AM-1200, two members of Alpha Micro's most popular series of computers and some of the closest things they made in the early '80s to desktop workstations. From the outside, the Eagle comes in a PC-style case, but it's not a PC: ampm.floodgap.com using the webserver provided with AlphaTCP — yes, Alpha Micros can be networked — and its own on-board Ethernet. At the time the cooling fan failure was putting a lot of strain on the hard disk because it was overheating, and since this was my first Alpha Micro and I wanted to keep it in good nick, I decided I would put a SCSI2SD in it after the repair and get rid of the spinning disk entirely. Fast-forward to last fall, a little over a year ago, when I tried to do exactly that with a ZuluSCSI. And then it wouldn't start. thought was a replacement unit I could raid for parts, but it turned out to be something rather more special — and then I was even more fortunate when I got the Eagle 300 back out of storage to make one last attempt at reviving it. To cap it off we'll go stick ZuluSCSIs in everybody else, including my Motorola ColdFire-based Eagle 450, the first ColdFire server ever produced and what used to be the fastest Eagle in the house until the new hotness came. I even converted the external BlueSCSI the AM-1200 was using to an internal ZuluSCSI too. Now nearly everybody's got a solid-state boot disk and they're all a good bit more zippy, so we'll gawk at the internals, compare 68K CPU and storage benchmarks and most importantly learn from my mistakes, because as my late father always said, "I'd rather be lucky than good." On a more solemn note, we'll also observe a moment of silence for one of the line's creators who passed away last year. It's time for a Refurb Multi-Weekend Sequel. Alpha Microsystems, founded in Orange County, California in 1977, produced what were considered some of the earliest "poor man's minicomputers," smaller and more affordable multi-user systems that run a bespoke, Digital Equipment Corporation-influenced operating system named AMOS. In our previous entry we discussed their history in detail. First-generation Alpha Micros like the AM-100, designed by Dick Wilcox who also wrote most of the operating system, used large S-100 cases and a CPU chipset called the WD-16, derived from the Western Digital MCP-1600 chipset — the same one used in DEC's LSI-11 CPU — but with higher performance microcode developed by Rich Notari. These machines thoroughly outclassed low-end PDP-11s yet were substantially cheaper, and Alpha Micro found a ready audience initially with hobbyists and then later corporate turnkey environments, where its integrated AlphaBASIC and database functionality gave it a competitive advantage. As the WD-16 had little elbow room to evolve, in 1982 Alpha Micro introduced new systems based on the Motorola 68000, porting AlphaBASIC and AMOS to run natively, but swapping address lines to make it appear little-endian for compatibility with WD-16 data files and AlphaBASIC P-code. These new machines included the AM-1000, Alpha Micro's most popular single model, and by 1984 it constituted the majority of the over 20,000 Alpha Micro machines then in active use. An idealized Alpha Micro office from the 1980s might look like this photo, from their actual advertising of the period. The main system is an AM-1042E, the S-100 box sitting on the pedestal next to the printer, using an AM-100/L CPU with an 8MHz 68000 (the same as the AM-1000, which was integrated into a desktop case), and in the factory-standard configuration shipped with 512K of RAM and a 60MB Winchester ST-506 hard disk. The system served some number of local users connected directly via serial ports, in this case the two administrative assistants with AM-60 terminals (a modified and rebadged Wyse WY-100). The fact everyone here was in the same room with the machine was helpful, because AMOS is a strictly real-memory operating system and executable code ran from where it was loaded in the user's fixed memory allocation — there was no memory protection. Although the admin assistants' explicit permissions were limited by which account they were logged into, using the same style of project-programmer numbers as DEC (e.g., [1,2] being the operator account), an errant job of theirs could readily stomp on another and it was not rare for busy systems with buggy software to regularly crash. On the other hand, this also made it fast and efficient with little separation between you and the hardware, and even Alpha Micros with fairly modest specifications could support hundreds of simultaneous users. Alpha Microsystems tried multiple times to broaden the line technologically, though these efforts were largely for naught. Early attempts to put equivalent hardware onto a PC ISA co-processor card, with software to interchange between MS-DOS and AMOS, yielded only an expensive and poorly-selling PC that wasn't good at either OS (eventually the company gave up producing turnkey systems and just sold the card). In 1984 Alpha Micro introduced UNIMOS, a licensed version of AT&T System V UNIX which ran on modified AM-1000 hardware with an MMU, but it was likewise too expensive and garnered little interest from new users nor demand from existing ones. The cost of its development, the Unix license and its associated royalties, and a simultaneous lawsuit from DEC over AMOS's similarities subsequently caused lasting damage to the company, and by the end of the decade Alpha Micro found itself almost entirely dependent on legacy AMOS users. In the wake of Wilcox's 1990 retirement and original investor Bob Hitchcock's own departure in 1991, new management tried once more with Unix systems based on the Motorola 88000 — which Motorola abandoned shortly afterwards for the PowerPC AIM alliance, and so no hardware ever shipped. anybody — yes, really, just two months after the '030's October introduction — initially offering a 20MHz CPU, 32K of L2 cache and supporting up to 360 simultaneous terminals, but even the lowliest 30-user configuration started north of $40,000 [about $117,600 in 2026 dollars]. By contrast, Alpha Micro was uncharacteristically tardy in adopting the 68040 and didn't release the 33MHz AM-4000 until 1993. It was nevertheless nearly as expensive, and for most small offices, which were now increasingly Alpha Micro's financial anchor, that kind of money was simply beyond consideration. In 1993 the company settled on a two-board approach to solve both problems at once. The CPU board, dubbed the Roadrunner and designed by engineer Joshua Stumpf, contained the new processor, standard RAM SIMM slots, L2 cache (if present), and SCSI controller. This board was specifically designed to also fit in legacy machines, specifically the desktop AM-1000, AM-1200 and AM-1600 and server AM-2000 and AM-3000 systems, and initially came in a 68030 and two 68040 versions. A second board served as the CPU board's system interface, linked together using a custom "X-BUS" interconnect over twin 34-pin cables. For legacy installs, this second board was an active interposer physically replacing the original processor, which in elderly units sometimes needed to be desoldered (though that was also true for the few third-party CPU upgrades then extant, like InterLink's Dimension-030, so the Roadrunner was at least no worse). But this second board could be a whole new system architecture of its own, and that was what the I/O board was, designed by Rod Hewitt. It carried the power supply connectors, controlled the system front panel, contained the System Security Device for licensing (more on this later), presented built-in external ports for parallel, SCSI and (for certain loadouts) Ethernet, had an internal port for an optional floppy drive, and provided SIMM-format "paddle card" slots for option cards. Best of all, these boards were smaller and — by using off-the-shelf commodity hardware — cheaper to manufacture, and could be paired into multiple configurations, together becoming the company's long-promised updated low-end and mid-range systems. reasons I've related elsewhere, and I managed to land it for just a couple hundred bucks in fully working order. (Boy, are those days gone.) Based on the software still on the hard disk, this machine was previously used at a chain of three party stores in Washington state as a centralised rental and point-of-sale system, a common turnkey application. On arrival it sported the same loadout as in this article's first picture except for its original smaller-capacity Tandberg QIC tape drive, which in Alpha Micro parlance is called a tape streamer. Since these systems don't boot from CD, QIC tape is your only way to cold start and restore most 68K Alpha Micro computers if the hard disk fails. These systems also don't support the old Alpha Micro VHS backup system, hopefully to be the subject of a future article, which was ubiquitous in their early hardware. There is a single hard disk in the second 5.25" bay, though these first-generation systems also supported 5.25" and 3.5" floppy drives using an AM-219 controller board. original Refurb Weekend. our previous Alpha Micro foray we discussed the SSD's role, a chip installed in every 68K (and later x86) Alpha Micro, even the earliest S-100 boards, used by the operating system and any installed VAR software packages to enforce copy protection and license caps. The SSD number on the rear is just a serial number, printed on the rear plate for convenience and engraved on the SSD chip inside, which I'll show you in a moment. This number is not the key stored inside the chip, up to 256 bytes in length, which only Alpha Micro recorded. When a VAR wanted to lock an install to a particular system, they would provide their private code to Alpha Micro plus the user's SSD serial number, and Alpha Micro would look up the key and generate an alphanumeric PIC (Product Installation Code) that the VAR either used for direct installation or to provide to the user. During the installation process the PIC (usually irreversibly) encoded a binary overlay for the protected executable(s), making it impossible to run them on a system where the SSD didn't match. To facilitate logic board swaps and upgrades, the SSD is socketed and easily transplanted into a new board, but PICs were expensive then and unobtanium now, another reason hard disk backups were so critical. % curl -I http://ampm.floodgap.com/ HTTP/1.0 200 OK Date: Sun, 11 Oct 2026 23:43:03 GMT Server: AMOS-HTTPD/1.3C(111) MIME-version: 1.0 Content-type: text/html Last-modified: Sun, 11 Oct 2026 23:42:00 GMT Content-length: 30242 Content-encoding: 7bit in our most recent article. In this picture it's also attached to an AM-401 CD-ROM, which is the trusty Toshiba XM-5401B in an external case, though only specific ROM versions are supported. It can't boot from this drive, but it can read AMOS-formatted partitions, and with external software can also access ISO 9660 filesystems. Onscreen is a performance estimate using the built-in SI.LIT tool, which we'll be using to benchmark our new solid-state disks when we get them in there. Here's that output. .si dsk0: SI--AMOS System Information, (C) Copyright 1990, Alpha Microsystems Inc. Version 3.0(114) Computer Type: Eagle Main Processor: 68030 Co-Processor: None MMU present: Yes Operating System: AMOS 2.3A(484) Boot PROM revision: M00 Number of SSDs: 1 Total Memory: 16384 K-bytes Resident Monitor Memory: 6218 K-bytes Computing Index (CX), relative to AM-100: 36.9 48 bit FP Index (4X), relative to AM-100: 36.3 Floating Point Index (FX), relative to AM-100/L: 5.6 Disk Index (DX), relative to ST-506: 15.3 I don't know why it identified the 68EC030 as having an MMU, because it doesn't, but we're mostly interested in the "computing index" figure (SI's equivalent of an integer score) which is 36.9 times faster than Alpha Micro's original AM-100, and the "disk index" hard disk throughput test, which rates the spinning disk it came with as 15.3 times faster than their early ST-506 drives. Remember these figures as a baseline; we'll be referring to them again. On the front panel in both pictures you can see the number "0" in the LEDs. That's where the system status is displayed, initially by the firmware, then the OS monitor during boot and then in operation. We'll come back to this as well. original Refurb Weekend involved replacing the old AT supply with an ATX one and a converter. Since that post I found a NOS AT supply for cheap and I needed the ATX supply for something else, so I removed the converter and installed the new AT supply. This is that unit. The CPU and the 53C710 are both clocked by an 80MHz crystal divided down to 40MHz; there are also 16MHz and 50MHz oscillators on the board which appear to be used for the PLD and bus logic. Likely for cost reasons there is no L2 cache, though another thing to keep in mind is — so I'm told — that for compatibility reasons with 68000 and 68010-era AMOS software it is not possible to enable the data cache (or at least not without substantial difficulty). In fact, we observed exactly this phenomenon when looking at the driver for the InterLink Dimension-030 CPU upgrade, which puts a 68030 in an AM-1000: it never set the data cache bit in the '030's CACR at all. Although some machines can accept an external L2 cache, including one we'll look at in detail, anything it would provide is strictly I-cache. but is functionally equivalent in AMOS. not). I have such an example later on. Other serial paddlecards can also be installed. The AM-314 provides only four serial ports, but is not merely a cut-down AM-318 — the AM-314 can also be configured for RS-422 (the AM-318 is strictly RS-232) and supports all RS-232 handshake lines (the AM-318 only RTS/CTS), and in certain configurations can trigger a remote reboot from a connected distant console by grounding pin 1 with pin 7. By contrast, the more exotic AM-338 provides an IBM Binary Synchronous Communication "Bisync" link, typically used for Remote Job Entry (RJE) or CICS connections with IBM mainframes, but could theoretically have also worked with some early point-to-point networks like BITNET. It connects to an AM-339 which provides the physical port. a future article. Notice how many of these PCBs say "Made in USA"! A different era. from my SGI Indigo^2 retrofit to see if it could sit on them. It did, so I sheathed them in electrical tape as a "bed," put the ZuluSCSI into initiator mode, connected the old hard disk and the ZuluSCSI to my copy rig, and left it to image the drive to the SD card. didn't change: the boot sequence wasn't starting. I freaked out, immediately powered it off, and checked everything inside that I'd touched to find I had not properly reconnected the CPU board's power connector. original. I dug up Rod's old E-mail to see if there were any clues in it and recalled what he'd said about the PLDs being dynamically reprogrammed on every startup — from the CPU board. I also knew from the service manual that the X-BUS cables, the only connection between the I/O board and the CPU board, had to be correctly connected or the service manual warned damage could result. A horrible theory stirred in my head: perhaps I had managed to accidentally corrupt the PLDs by effectively bringing up the I/O board without the CPU board, where the boot PROMs used to reprogram them are located. However, that also suggested a solution — there are many undocumented jumpers on the AM-319 and I wondered if one of them could be used to trigger a clean reset of the programmable logic. in a future article). He also had an interest in digital television, developing TSReader, a way to analyse the MPEG-2 transport streams commonly used for satellite, cable and IPTV transmissions. ZTERM and in particular TSReader became far and away his most popular software packages. However, a few years prior and unbeknownst to many, he had quietly entrusted a copy of the TSReader source code to a friend officially "just in case," and sold ZTERM to MicroSabio, a long-time Alpha Micro support company that maintains A-Shell, a way of running AlphaBASIC applications on modern operating systems. The reason became clear later — he was dying, and it was not treatable. The source code for TSReader was duly posted after his passing and remains today as his most popular legacy. Rest in peace, Rod, and thank you. Without Rod's guidance, though, there wasn't much more I could think of to do at that point. I unplugged it, pulled the clock battery and let it sit for a couple days to see if that was enough to reset the PLDs, assuming that was the actual problem, and it didn't. It still seemed like it should be repairable if I could only figure out how, but as there was little point in having it sit fruitlessly on the workbench I removed all the remaining cables from the system board and moved the machine to cold storage until I could come up with something else. In the meantime I turned to my alternative system to get ampm.floodgap.com back up and running, though to discuss it we need to bring the history forward some more. only in the E500: a junior-varsity 68040, which is what the E400 was, didn't have much appeal. Both the E200 and E400 were quietly dropped. For large installs that required substantial numbers of serial ports, the existing AM-319 board had to be expanded. The revised AM-319-20 board, providing four built-in serial and parallel ports with a UPS monitor port and a higher-performance DP83902 Ethernet NIC, still had two paddlecard slots, but these slots were widened to 60 pins and could now be part of a bus connected to an external chassis. Alpha Micro had long sold the AM-990, a large capacity case (in this image as used for the AM-4000, though I apologise I don't have a better image of it) and the AM-990 Jumbo, which was even larger. A new higher-performance serial card was developed to take advantage of the widened paddlecard slots, an optically-isolated eight-port card called the AM-359. Twelve AM-359s could be installed in the AM-990, yielding 96 ports when connected to a fan-out in one of the AM-319-20's paddlecard slots (the four on-board ones made an even hundred); the Jumbo could take another twelve AM-359s for another 96 ports connected to the second, a whopping total of 196 serial ports when combined with the base four. If you needed even more, the AM-3501 sidecar chassis could take you well beyond. There was no point in supporting the 68EC030 with such a monster: this new Eagle, officially the Eagle 550 Super Eagle, was 68040 or bust. that large, a Super Eagle in the standard case could support up to 60 ports, four on the AM-319-20 and then seven AM-359 cards in the usual position. The E550 Super Eagle additionally came as a separate upgrade kit for the E500 and the few E400s that sold, essentially a system board swap, though when sold as a turnkey system it was always with the 40/80MHz CPU. The E550 introduced a new Seiko timekeeper chip as well which not only maintained the time but also the "CMOS settings," the first Alpha Micro with an on-screen setup utility in ROM allowing boot configuration. Subsequently the company was tardy once again in adopting Motorola's newest 68K CPU, this time the superscalar 68060, which had come out in 1994 aimed squarely at the Intel Pentium but didn't reach Alpha Micro customers until mid-1997. This took two forms, a new 66MHz '060 Roadrunner upgrade option for the E550 Super Eagle and the AM-4000 (lesser Eagles need not apply), and a new AM-6000 large system. Interestingly, the AM-6000 is strongly based on the E550, reflected in its internal designation as the AM-3500-6000 making it a "stealth" Eagle. The '060 Roadrunner not only included the new CPU but also 64K of L2 cache, support for up to 256MB of RAM in four SIMM slots, and 68-pin Fast and Wide SCSI-2 using the NCR 53C770. along with E100s and a smattering of E500s and Super Eagles. However, it was not lost on company management that Motorola believed the 68000 family was fast approaching a performance wall. This was made most clear by their then-enthusiastic participation in the PowerPC AIM alliance, but also the rise of ColdFire, which Motorola had first announced in 1994 as well. ColdFire was in its own way Motorola's oblique admission that 68K was losing desktop competitiveness to x86, an attempt to scale the ISA down to embedded markets where its familiarity could be an asset. Approximately 20% of the instruction set such as BCD and certain addressing modes were eliminated, meaning the canonical ColdFire could not be fully binary-compatible with any extant 68K. On the other hand, such cuts enabled the core to execute nearly every remaining instruction in a single clock cycle, and the initial die was a miniscule 4.4mm² at 0.5μm, a third the size of Motorola's own 68300-series CPU32+. Some amount of this work was done by altering the microcode of the 68040V, a fully static 68LC040. Mindful that ColdFire's incompatibility might impair adoption, Motorola chose to create a bridge first-generation chip from this altered 68040V where omitted user mode instructions were left in, demonstrated on die photos. While the new chip had smaller 2K instruction and 1K data caches than the 68040V, and the MMU was also eliminated, this deviation from spec was still sufficient to run regular 68EC040 code at the user level. Motorola called this first-generation ColdFire chip the MCF5102, produced on a 0.6μm process, and introduced it in 1995 drawing 0.8W at 20MHz and reaching 33MHz. Clock-for-clock there was no way this chip could eclipse an '060, and the emerging "true" ColdFire 520x series couldn't run existing Alpha Micro software, but the MCF5102 was still faster than an '030 and nearly as fast as an '040 — in fact, we'll prove it. On top of that it was cheaper and AMOS didn't need the MMU anyway, making for a plausible mid-range machine that wouldn't imperil (much) sales of the E500 or E550. alt.sys.alpha-micro, though credit must be given to John F. G. Leighton, then Alpha Micro's VAR marketing manager, who chose to print the review unedited in marketing materials, even Rod's gentle complaints. Since this is the only E450 I have personally laid my hands on, we will be referring to his comments liberally as a point of comparison, and consequently the E450's history is probably the best documented of any 68K Eagle. It rolled out to users in October at the annual meeting in nearby Riverside, California. This particular system was a gift from someone who inherited it from an 9-1-1 emergency dispatch centre and wanted to find it a good home, another way that running an Alpha Micro-powered web server has paid off. I was able to quickly get into the system (if it's not clear by now, I love hacking into Alpha Micros) and reconfigure it, and it had lurked as the E300's work spare and a test unit since then. Like the E300 it has a bootable tape drive, but this time it's a more modern DDS/DAT. E450, and it claims not to have an SSD at all (untrue). As such, I'm not sure I can believe the stated manufacturing date of September 2002, and at least one date inside directly contradicts it. It's possible this was a case with a transplanted board. 1999 as prerequisites for the AM-370, an unidentified off-the-shelf 100Mbit PCI NIC that goes into the "slot" at J5. To access these PCI slots, that rear panel I pointed out needs to be removed. The AM-370's availability implies all shipping E450s should have had them by then — there was even an alleged board-swap program to do so. I've yet to find another one, so I don't know if that's true, but it would be interesting to find out because with this card or the OEM equivalent you would have two fully operational NICs and multihoming was reportedly supported. I also don't know what's going on with the unpopulated "option connector" at P5 to the right/east of the AT power connectors. other slots. The E450 is one of only a few Alpha Micro systems that can accept an optional external L2 cache, though as mentioned this cache is only enabled for instructions, and the form factor does not match any PC cache stick — in fact, it's the same as a 72-pin SIMM, so don't put the wrong one in the wrong place (Rod also objected to this). The only size supported is 64K, the same cache stick used for the AM-6000 and the '060 Roadrunner, part #PDB-00701-00. I've never seen this cache stick and comparison of his numbers with my cacheless E450 suggests it only yields around a fourteen percent boost, not nothing but not much, likely because it can't do anything for the data cache (though stand by for a very important observation on actual clock speed). The E450 also has two 72-pin SIMM slots, which need not be paired and support up to 256MB, though as with the earlier systems the machine needs to be jumpered to tell it how much is there. The tag on the one in J11 (service order 13009, apparently) is dated January 18, 2002: that makes this machine at least eight months older than its alleged manufacturing date, and to have received an upgrade suggests it's even older than that. Between the two sticks this system has 72MB of RAM. Below/south of the RAM SIMMs are the three paddlecard slots. Also in this image is another obvious non-populated area: a pin-grid array marked "PGA040" at U89 in the northeast/upper right hand corner. That sounds like somewhere the CPU would go, and the footprint looks like an '040. So where's the actual processor? fast is it doing it, though? While Rod's review stated his prerelease system was apparently running at 33MHz, the oscillator closest to the CPU can be seen clearly in this photograph, and it's ... 25MHz. There are no other crystals on the board except for the serial port one you saw earlier, the official marketing announcement has a board layout that also clearly labels this crystal as 25MHz, and nothing in the MCF5102 user's manual says the chip does anything tricky with the clock. As it happens, the only place in Alpha Micro documentation where the E450's CPU speed is given is Rod's review: everywhere else, even the data sheet, simply says it's a ColdFire and nothing more. Since mine is only 14% slower than his, and his had the cache, his can't possibly have been running at 33MHz either. The E450 is a 25MHz ColdFire, full stop. In a backwards way, however, this is nothing less than validation of how performant early ColdFires could be. Recall that our E300, a 40MHz 68EC030, had a "CX" computing index score on the SI.LIT benchmark of 36.9. The same benchmark on this E450 with a 25MHz MCF5102 gets a score of 59.9, and Rod's with 64K L2 came in at a whopping 68 (Alpha Micro said 68.5; either one is around 14% higher). By contrast, the E550 Super Eagle, with a full 40MHz ("80MHz") 68040 Roadrunner clocked 60% faster and 32K of L2 cache, officially gets ... 79.9 (note from the future: my figure is 83.6) — the full cached-up faster-clocked 68040's performance on the same code is only around 33-40% better, and just 16-22% or so if the E450 has its cache too. Put another way, the CX/MHz ratio of the faster 68040 was right around 2.0, while the CX/MHz ratio of the MCF5102 is 2.4 without the cache, and almost 2.75 with it. Likely because the lower clock speed would have looked bad in marketing materials, similar to why General Magic never mentioned the clock speed of the DataRover 840, Alpha Micro simply chose not to mention it either. Still, this machine's surprising efficiency proves ColdFire, at least early on, definitely had legs. I'm not sure how Rod got it wrong except that an earlier version may indeed have run that part, though with these numbers, if there had ever been a production 33MHz E450 it might have seriously endangered sales of Alpha Micro's remaining '040s — perhaps that's why they didn't use it even though the faster part existed. Best guess is that the AM-138 was originally designed for the 68040 and then quickly retrofitted for ColdFire, leaving the PGA region as an "R&D test point" (as documented). our prior entry, and he referred me to a longtime Alpha Micro vendor that they still partner with for existing installations. It took a few months, but this vendor was able to locate what appeared to be another E300 with working boards and we negotiated a price and getting it shipped. "everything console" connected to the top left port (G1) via the dongle at the typical speed of 19200bps. Good, it booted fine, we got a dot prompt, we can get into it, networking is already configured, and (as is typical for most Alpha Micro installations of the era) there is no password on the operator account. I powered it off and now that we know where the system thinks the console is, we'll get a proper self-test readout. I powered it back on with the reset button held in and the self-test came right up. The self-test can autosense the baud rate by mashing the spacebar when the front LED flashes "5b," and then the test runs, with the LED showing the current state and additional details sent to the serial port. ---------------- SYSTEM SELF-TEST ---------------- Version 2.1(120) Prom Rev. N00 for the AM-174 board. polling complete. Boot configuration: Processor - 68040 Memory detected - 32M bytes Primary serial ports - 4 SCSI Controller press [space] to bypass memory test MEMORY TEST passed - 32M bytes TIMER TEST passed SERIAL PORT TEST Primary serial ports - 4 Port # 0 passed Port # 1 passed Port # 2 passed Port # 3 passed SCSI Controller Controller Self-test passed SCSI drive Self-test passed Find diagnostic cylinder passed Write/read test passed 40?! This is not a Eagle 300! We need to open this thing up. didn't expect was the CPU board on the bottom: it's a full 68040, just like the test said. Bclk for the bus clock, and then a second exactly twice as fast labeled Pclk as the so-called processor clock. In the 68020 and 68030, which accept a single clock signal, their internal ALU runs at only half the bus speed such that the 40MHz 68EC030 in the Eagle 300 actually has an ALU running at just 20MHz. For the 68040 Motorola removed this limitation to run its ALU at full bus speed, but the chip designers also studied trace data to optimize for the most common instructions, implementing a 7-stage pipeline where most effective address calculations and fetches occur with no penalty. The upshot of this was to cut most instructions' cycle count in half or more. The 2x processor clock is truly used, but not to speed up the ALU, so it's wrong to say the 68040 is "double-clocked." In a two-part 1990 article in IEEE Micro, Motorola explains that "Pclk provides timing reference points within each Bclk period," employing it for synchronous sub-cycle timing, and furthermore explicitly states that "all internal operations cycle at the Bclk rate." Still, the fact this clock signal was present at all gave Apple an excuse to tout both timings for '040 Macintoshes, and Alpha Micro cheerfully reported just the faster one, even though the chip only appears to run at that comparative speed from its larger 4K L1 cache, unhindered ALU and reduced cycles per instruction. On this board, Pclk is provided by the same 80MHz crystal we saw on the AM-172, divided down by two to yield Bclk in the same way the 68EC030 board does for its single 40MHz clock. (For the E400's AM-174-00, this crystal would have been 66MHz divided down to 33MHz.) The single parity FPM SIMM slot and 16MHz and 50MHz oscillators are also present, as well as the same 53C710 SCSI controller, here a genuine NCR part. However, new for this board is 32K of L2 cache at the upper right/northeast corner, implemented with two IDT 71B74 8K cache-tag RAMs together providing 29 bits (512MB) of address comparison, and then four Cypress CY78C185 8K SRAMs for the cache itself. Remember, however, that in AMOS all cache is I-cache. Effectively this 40/80MHz AM-174 makes our new system a full Eagle 500, so why is it labeled as "only" an E300? I don't how how these systems originally shipped from the factory nor whether the E500 designation actually appeared on the back, but Alpha Micro did run a promotion in late 1997 where you could upgrade any Roadrunner '030 to a Roadrunner '040 by swapping the CPU board. My guess is this is one of those systems, and because that upgrade kit wouldn't have changed the plate on the back itself, the reseller simply noted it to be a working E300 and sold it to me as such. While that wasn't exactly what I was hoping for, it's a really nice bonus, as evidenced by the system benchmark (taken on the SCSI hard disk it shipped with): That score officially makes it the new fastest Alpha Micro in the shop by far (this is where that prior 83.6 number came from, compared to the E450's 59.9 and E300's 36.9). It seemed a shame to carve it up as spare parts, so let's have a little look around. A surprising thing about the system configuration file (SYS:AMOS32.INI, a/k/a AMOS32.INI[1,4]) is that only one terminal is actually defined, which makes you wonder what those two RJ-21s are doing. Best guess is that this machine passed through a couple hands and ended its prior service as a single user's toy, much as my own machines are now. In a related phenomenon an annoyingly small number of terminal types are defined, all inconvenient, likely to save memory. On the other hand, the full AlphaTCP suite (based on SpiderTCP and SpiderStreams, best known as the Windows NT TCP/IP stack before 3.5) is defined and present, and we saw it running before, so we ought to be able to make use of that. That's its IP address, and we saw Telnet was running (TCP:TELNED.LIT), but there's a snag: The TCP:CONFIG. file sets up TCPEMU, AlphaTCP's master daemon, acting as its service description file (really a sort of up-script). This line for the Telnet daemon causes an automatic log-on from a Telnet session and inconveniently forces the FWYCOL terminal type, intended for a real Wyse WY-370. That's also the terminal setting for the single serial port which our "everything console" doesn't speak, meaning I can't visually edit anything without making a big mess. Ironically, that AM-75 colour head my E300 uses is itself a modified WY-370, but no longer speaks that terminal emulation either. But we have another option! Now knowing its IP address, I set up a small wired network to my MacBook Air. Although some terminal programs like Kermit 95 can speak WY-370 over Telnet, using MacWise — now freeware and runs on Tiger and Power Macs all the way to Tahoe on Apple silicon — I managed to discover that its TeleVideo 925 emulation will partially match FWYCOL. This was just enough to, with some care, edit TCP:CONFIG. and remove all the defaults so that I could manually select the terminal type on Telnet login. I then reset the FTP user credentials in TCP:FTPUSR., uploaded a copy of ANSI.TDV from the Eagle 450, and changed the TDVDEF line in a test copy of SYS:AMOS32.INI to allow it as a terminal type, which at last got me a proper session. I'm not sure of this system's most recent owner and the seller didn't know either, but there were two interesting domains in its TCP:HOSTS. file (identical to /etc/hosts) for that IP address. One domain name belongs to someone who appears to have been a recording engineer (!). This domain still exists, but is only partially functional, so I've chosen not to link it here. The other domain name was for a personal genealogy site, now parked, and that site appeared to be what it was currently offering via the Web server on HTM:, mapped to PPN [7,77]. However, because the HTML files were not on an extended directory device, I can't tell when the site was created because the old AM file system doesn't preserve modification times: Looking up this domain in the Wayback Machine, it seems to have been active in the early 2000s. Still, not bad assuming it was still serving it then. differently on the AM-172 and AM-174s, so it seemed safer just to never separate them in the first place. I wasn't even going to move the SSD and hard disk — since TCP/IP networking was already set up on the E500, I could just upload the site to the E500's hard disk instead. Only the E300's power supply, serial port cards and Tandberg QIC streamer would stay. Once the new transplanted system was working, then I'd see about doing the ZuluSCSI upgrade again. It tried to boot. Startled, I powered it off, connected the everything console, and turned it back on with the reset button held in to force a self-test. Except for the missing hard disk, it passed the self-test — even the SCSI controller tested good. I decided to push my luck and connect the ZuluSCSI, and this time it did throw a 2d. I freaked out again, powered it off, let it sit and then gingerly turned it back on. It still did it. However, when I disconnected the ZuluSCSI, it went back to trying to boot, and a repeated self-test was still clean. This was clearly new behaviour — beforehand, it wouldn't do anything, not even enter the self-test, let alone attempt booting. Recall that error 2d had two mentions in the manual, the second one referencing the primary and secondary boot devices. Since the self-test said the SCSI controller was fine, this made me suspicious that there was something about the ZuluSCSI's configuration the machine didn't like. Knowing some systems can get finicky about sluggish devices immediately after power-up, I reconnected the ZuluSCSI and powered the E300 back on. Code 2d duly appeared, but this time instead of turning it off, I hit the reset button just to see what it would do. SI.LIT had actually dropped to around 10, which was 33% slower than its original hard disk. .scsi Dispatched SCSI port: SCSI id 7: (reserved) SCSI bus host adaptor SCSI id 6: No device or unable to report SCSI id 5: No device or unable to report SCSI id 4: No device or unable to report SCSI id 3: SCSI-2 (tape) TANDBERG TDC 4200 =08:01CREATED12119 SCSI id 2: No device or unable to report SCSI id 1: No device or unable to report SCSI id 0: SCSI-2 (disk) ZULUSCSIHARDDRIVE 2.3BZuluSCSI .si dsk0: SI--AMOS System Information, (C) Copyright 1990, Alpha Microsystems Inc. Version 3.0(114) Computer Type: Eagle Main Processor: 68030 Co-Processor: None MMU present: Yes Operating System: AMOS 2.3A(484) Boot PROM revision: M00 Number of SSDs: 1 Total Memory: 16384 K-bytes Resident Monitor Memory: 6218 K-bytes Computing Index (CX), relative to AM-100: 36.8 48 bit FP Index (4X), relative to AM-100: 36.3 Floating Point Index (FX), relative to AM-100/L: 5.6 Disk Index (DX), relative to ST-506: 41.2 .si dsk0: SI--AMOS System Information, (C) Copyright 1990, Alpha Microsystems Inc. Version 3.0(114) Computer Type: Eagle Main Processor: 68030 Co-Processor: None MMU present: Yes Operating System: AMOS 2.3A(484) Boot PROM revision: M00 Number of SSDs: 1 Total Memory: 16384 K-bytes Resident Monitor Memory: 6218 K-bytes Computing Index (CX), relative to AM-100: 36.9 48 bit FP Index (4X), relative to AM-100: 36.3 Floating Point Index (FX), relative to AM-100/L: 5.6 Disk Index (DX), relative to ST-506: 100.4 six times faster than the original hard disk). There's no obvious caching in the Blaster's firmware that I could see, and although the AMOS system-wide disk cache was on, the test is supposed to be unaffected by OS-level caching. On the other hand, when I rebooted AMOS from software, its score went back to 41 and 100 thereafter. More on this phenomenon later. Termination power was sufficient to power the Blaster. But what the Blaster didn't fix, even with its later firmware, was the 2d code the E300 kept throwing from a cold start. Although booting after a manual reset was still fine, it refused to start after a power cycle without assistance, which I need it to be able to do if there's a power outage when I'm not around. .ini file, but since the issue appeared to be what the E300 thought was the secondary device and I knew the streamer was connected and working, I had a look at the back boot DIP switches first. The previous setting was #1 and #3 on, which would attempt a boot from the (non-existent) floppy drive first, and then try the SCSI hard disk. This had always worked before, but we have no floppy drive and I'm not likely to find an AM-219 anytime soon, so I tried the other boot position where it attempts a boot from the streamer first — again, known good electronics — by switching #4 on. And that worked: now it boots reliably. The conversion is complete. So, with the E300 resurrected and finally successfully converted to solid state, let's really push our luck here ... by doing the same with the others! (I should note I excluded the E100s this time around; I haven't found a special task or physical location for them yet.) SI.LIT disk score of 30.9. For this system I bought a ZuluSCSI Wide, which tops out at 34 MB/s read and 15 MB/s write, and which I already use in my Apple Network Servers with a similar NCR 53C825A. .scsi Dispatched SCSI port: SCSI id 15: No device or unable to report SCSI id 14: No device or unable to report SCSI id 13: No device or unable to report SCSI id 12: No device or unable to report SCSI id 11: No device or unable to report SCSI id 10: No device or unable to report SCSI id 9: No device or unable to report SCSI id 8: No device or unable to report SCSI id 7: (reserved) SCSI bus host adaptor SCSI id 6: No device or unable to report SCSI id 5: No device or unable to report SCSI id 4: No device or unable to report SCSI id 3: No device or unable to report SCSI id 2: SCSI-2 (tape) HP C1533A A907 9 SCSI id 1: No device or unable to report SCSI id 0: SCSI-2 (disk) ZULUSCSIHARDDRIVE 2.3WZuluSCSI .si dsk0: SI--AMOS System Information, (C) Copyright 1990, Alpha Microsystems Inc. Version 3.0(114) Computer Type: Eagle Main Processor: 68040 Co-Processor: None MMU present: Yes Operating System: AMOS 2.3A(484)-15 Boot PROM revision: D00 Number of SSDs: 1 Total Memory: 73728 K-bytes Resident Monitor Memory: 4366 K-bytes Computing Index (CX), relative to AM-100: 59.9 48 bit FP Index (4X), relative to AM-100: 58.2 Floating Point Index (FX), relative to AM-100/L: 7.9 Disk Index (DX), relative to ST-506: 51.0 .si dsk0: [...] Disk Index (DX), relative to ST-506: 52.2 . the last Alpha Micro article we booted our AM-1200 desktop system using a BlueSCSI attached to its external 50-pin Centronics-style SASI port, which with some tweaks to the settings file can be made compatible enough for its very old bus. But I'd like to use that device for other things, so we'll put the old ZuluSCSI card — more than fast enough for this thing — inside. To avoid me having to dismantle it every time I want to switch the disk image, I disconnected one of its unused serial ports and threaded a USB cable there. SUB0:. It's as fast as the BlueSCSI was, probably because both devices can easily saturate its slow SASI bus: AMOS 1.4 misdetects its 68010 as a 68000 (AMOS 2.3A detects the CPU correctly), but like the E450, there was no second test bump either. "everything console." I should point out that the E500 has a slightly later version of AMOS than the E300 and E450 and we get a little more explanation with the bus readout: While all three systems support synchronous SCSI, this version of AMOS actually reports it, along with the width (8-bit, because it's only Fast SCSI, not Wide). Now, what about performance? The ST32272N we replaced is a 7200rpm drive while the ST310151N in the E300 was only 5400rpm, thus accounting for the E500's better baseline disk score, and the E500's faster CPU probably explains its slightly higher first-run result of 46.3. But the second run is even more lopsided than what we saw with the E300, a massive 180.7. Since two of the systems were doing it, it was time to dig in a little more. The ZuluSCSI Blaster has a debug mode switch which echoes status and current operation to a connected machine over USB serial at 115200bps, so I hooked up both the E500's serial console and the USB port of the Blaster simultaneously to the MacBook Air to watch what SCSI operations occurred during the benchmark test. very unusual: there wasn't any. In fact, even though the baseline score had sunk down to a dismal 10 or so because of all the debugging data it was emitting, the second run was still a blistering 180.7. This really sounded like operating system caching, but except for the AM-1200 where I wasn't running it to save memory, the other three systems were running the standard disk cache as virtually any performance Alpha Micro would — and allegedly SI.LIT should be unswayed by it. For some reason the E450's cache configuration wasn't locking UFDs (user file directories, i.e., PPNs), but turning that off on the E500 and E300 didn't make a difference, and all three were caching everything else including the MFD (master file directory). However, when I turned off caching altogether at runtime (using the CACHE.LIT tool and disabling with OFF), though the scores got really low, they were now consistent from run to run. Do note our observation isn't enough to fully explain the E450, which also runs the OS disk cache, but didn't have a second run bump. If you disable the cache on the E450, although its overall score declines, it still remains consistent from run to run. One possibility is that the driver for its later SCSI controller just isn't as aggressive. Although the overall issue certainly calls into question how useful SI.LIT is as a disk benchmark, despite being likely the only Alpha Micro benchmark tool you can expect most recent systems to come with, the question then becomes how comparative disk performance on an Alpha Micro should be measured. Was it still fine for me to continue with my usual practice of leaving the cache on and testing immediately after boot? It's probable that there'd be little in the cache by that point, whatever would be there would likely be similar from system to system (assuming the same version of the operating system), and likelier still that whatever was present in the cache wouldn't be very germane to SI.LIT. Under my current knowledge of AMOS I think these numbers are still broadly comparable; I just have to keep in mind that the score on subsequent runs is likely to be bogus. precisely even with our E450 here). The E100 was discontinued shortly afterwards in 2001. SI.LIT CX score of 816 (!) on dual Athlon 2800+ CPUs. Later AM-113 SuperFalcons were just serial ports and a socket for the SSD; the main system was now more than suitable to service them, and Motorola wasn't making any more 5102 CPUs either. The Eagle 800 that same year ran the same technology in miniature, bringing the great experiment to a close with the discontinuation of the last E250 and E450 systems, and today's systems sold by the reformulated Alpha Microsystems LLC use the same x86-based architecture. Over their production lifetime, analysis of known serial numbers suggests around ten thousand 68K Eagles were ultimately sold, and now I've got five of them. Rest in peace, Rod. They're still great machines.

Sometimes it's easier to identify an IC with a microscope. While sorting a box of old ICs, CuriousMarc came across some Harris ICs labeled "F1-10-5", a mysterious part number that didn't show up in any databooks. Since unidentifiable ICs are useless, he gave me one to analyze. Conveniently, it was in a ceramic package, so I could open it up with a quick tap from a chisel. Under the microscope, the chip's most striking feature was a grid of square capacitors. With all those capacitors, I guessed that it was a switched-capacitor filter. The die provided another clue: the part number HF-10. With this information, we quickly found that the chip was Harris's version of the standard MF10 switched-capacitor filter chip.1 The Harris integrated circuit, labeled F1-10-5 (or maybe FI-10-5), with a 1985 date code. Photo courtesy of CuriousMarc. Switched-capacitor filters were a popular way to implement analog filters in the 1980s. Rapidly switching capacitors in and out of a circuit enabled the construction of single-chip filters that were easy to use and performed well. The MF10, introduced by National Semiconductor in 1981, provides two flexible filters on a chip; each filter acts as a low-pass filter, band-pass filter, or a high-pass filter. The filter's characteristics are simple to control with a few external resistors. The Harris HF-10 die under the microscope with the main functional blocks labeled. (Click for a larger image.) Since I had the chip under the microscope, I took the opportunity to analyze it more closely. The white lines are the metal wiring that connects the chip's circuitry. Under the metal layer are two layers of polysilicon (reddish) and the underlying silicon (gray). The top and bottom halves of the chip are mostly mirror images, corresponding to the chip's two filters. The distinctive reddish squares in the middle of the chip are 72 tiny capacitors, constructed from polysilicon. Above the capacitors, CMOS switches turn on and off at the clock frequency, switching capacitors in and out of the circuit. Each filter uses three operational amplifiers (op amps), outlined in red. At the right are the three outputs from the three op amps: high pass, band pass, and low pass. The control circuitry is on the left: clock level shifting, clock shaping, frequency ratio handling, startup circuitry, and current sinks to provide fixed currents to other parts of the chip. Around the edges of the silicon die, 20 hair-thin bond wires connect the die to its 20 external pins. The die has some interesting chip art: a Harris logo and an outline of Florida; Harris was headquartered in Melbourne, Florida. The initials on the die are presumably the engineers who designed the chip. Some interesting images from the die. Switched capacitor circuits The filter is based on switched-capacitor circuits. A switched capacitor can replace a resistor in certain circuits, as shown below. The switches are controlled by a clock signal; the switches alternately close in clock phase 1 and phase 2 (ϕ1 and ϕ2). In phase 1, the capacitor is charged to the input voltage. In phase 2, the capacitor passes charge to the output. By rapidly toggling the switches, charge is (almost) steadily passed to the output. The larger the capacitance, the more charge that is passed through. Likewise, a higher frequency passes more charge. It can be shown that the circuit matches a resistor with resistance of 1/(fC): a higher capacitance and frequency correspond to lower resistance. A switched capacitor can replace a resistor. Why would you replace a simple resistor with this complicated switching circuit? In an integrated circuit, resistors are inaccurate and inconveniently large, especially high-value resistors. Replacing a large resistor with a small capacitor saves space on the die. Moreover, it is easy to generate an extremely accurate clock frequency with an inexpensive quartz crystal, making the filter's frequency highly accurate. Finally, the equivalent resistance can be changed simply by changing the clock frequency, making it easy to tune or sweep the filter. On-chip capacitors are fairly inaccurate, with the capacitance typically varying by 20% from chip to chip due to variations in manufacturing conditions. However, this isn't a problem in the MF10 because the circuitry was designed to depend on the ratio between capacitances, which is stable. Specifically, the MF10 uses 72 identical square capacitors, which will have almost identical capacitances. Careful examination shows that some of the capacitors are separate, while others are connected in groups of 8 to form larger capacitors.2 This yields a highly accurate ratio of 8:1 between the grouped capacitors and the individual capacitors, even though the absolute capacitance will vary from chip to chip. Each capacitor is constructed from two layers of polysilicon,3 forming the plates of the capacitor, separated by a thin layer of insulating oxide that acts as the dielectric. I estimate that each capacitor square is 5 picofarads. The grid of capacitors in the MF10. I've added yellow lines to show how the capacitors are grouped. The switches are above and below the capacitors. This chip uses one more trick with switched capacitors: it inverts the voltage while acting as a resistor. In the switched-capacitor circuit below, there are four switches. The capacitor charges to the input voltage during phase 1, the same as before. But duing phase 2, note that the top plate of the capacitor is grounded, while the output comes from the bottom plate. If the capacitor was charged to, say, 1 volt, the top plate is 1 volt above the bottom plate. So if the top plate is grounded, then the bottom plate must be at -1 V. (This is the same idea as a charge pump.) This circuit turns out to yield a more accurate filter because some parasitic capacitances cancel out. By using four switches, the switched capacitor can invert the voltage. The op-amp integrator The heart of most analog circuits is the operational amplifier, or op-amp. An op-amp takes two inputs and amplifies the difference by many orders of magnitude. Normally, an op-amp is configured with negative feedback, which forces the two inputs to be essentially the same. Op-amps are useful not only for amplification, but for filtering, buffering, summing, and other tasks. A basic op-amp integrator. The filter chip uses op-amps as integrators, to integrate an input voltage over time. The circuit above shows a simple op-amp integrator. The input voltage produces a current that flows through the resistor and charges the capacitor, so the capacitor holds the integral of the input voltage over time. You might expect that the left side of the capacitor would become positive as it charges. However, the op-amp's feedback forces both inputs to ground, so instead the right side of the capacitor becomes negative. Thus, the output is the negative integral.4 The MF10 chip uses the circuit above, except the resistor is replaced with a switched capacitor. The capacitor across the op-amp is not switched, but consists of either 8 or 16 capacitors from the capacitor grid. The CMOS switches The CMOS switch is the technology that makes the switched-capacitor filter possible. A CMOS switch has a fairly low resistance (maybe tens of ohms) when closed and an enormously high resistance (hundreds of megohms) when open. This high resistance ensures that the charge doesn't leak out of the capacitors. A CMOS switch is constructed by combining an NMOS transistor and a PMOS transistor. The NMOS transistor and PMOS transistor are opposites. An NMOS transistor is good at pulling the output low, while a PMOS transistor is good at pulling the output high, so in combination they provide an effective switch. An NMOS transistor is turned on by a high voltage on the gate, while a PMOS transistor is turned on by a low voltage on the gate. Thus, a CMOS switch requires two control signals of opposite polarity, which is a minor inconvenience. A CMOS switch. The diagram above shows how a switch is implemented with an NMOS transistor and a PMOS transistor in parallel. When the control line is high, and the inverted control line is low, both transistors turn on, providing a path through the switch circuit. When the control line is low (and the inverted line high), the transistors turn off, opening the switch. The chip uses CMOS switches in pairs, with one switch on and the other off. This forms the equivalent of a toggle switch that connects either A or B to the output. This circuit is simply two CMOS switches, with separate control lines for each switch, as shown below. In the MF10, the switch toggles at the clock frequency. During one clock phase, the switch is connected to A, while the switch is connected to B during the other clock phase. The schematic on the right, below, is the same circuit, but reorganized to match the layout on the die. A double-throw CMOS switch. The photo below shows a CMOS switch on the die, constructed from two PMOS transistors and two NMOS transistors. The four control lines run horizontally in polysilicon, forming a transistor gate where they cross doped silicon. The upper PMOS and NMOS transistors are driven by the clock phase 1 (Φ1) signals, while the lower transistors are driven by the phase 2 signals. CMOS switches on the die. The metal layer was removed to show the transistors. One problem with switched-capacitor filters is that the clock can generate switching noise that appears in the chip's outputs. The MF10 uses several techniques to reduce clock noise. Each set of transistors is surrounded by two isolation rings: one positive and one negative. These block noise from traveling through the silicon substrate. Note that the rings have opposite polarity for the NMOS transistors and the PMOS transistors. The light tan region in the photo above is a second layer of polysilicon. This polysilicon is connected to ground, providing a shield layer over the switching circuits. For the photo above, I removed the metal layer with acid5 to make the transistors more visible. The photo below shows the original die, with the metal layer connecting the transistors. The small black circles are connections between the metal layer and silicon or polysilicon. The same CMOS switches, showing the metal layer. Putting it together: the state variable filter There are many ways of creating a filter. The MF10 chip uses a technique called the state variable filter, invented in 1967. This circuit acts as three filters, with high-pass, band-pass, and low-pass outputs. Moreover, the circuit is flexible since the frequency, the gain, and the filter quality (Q) can be varied independently. It uses three op-amps: one to sum signals and two for integration. By changing how the values are summed, the characteristics of the filters can be changed. The diagram below shows a simplified representation of a state variable filter. The mathematics behind a state variable filter is complicated, so I won't get into it. In short, the signal, the integral, and the double integral form the three state variables that define the state of the system. Simplified diagram of a state variable filter, with two integrators. Inspired by North Coast Synthesis. The block diagram below shows how the filter is represented in the MF10 datasheet.6 The diagram is similar to the diagram above, with three op-amps. However, the summing circuitry has been separated out. Moreover, the feedback paths are not shown explictly. Instead, resistors are connected between the chip's external pins (squares) to configure the filter as desired. The mode switch at the top allows the low-pass feedback to be controlled by an external pin (SA/B). Block diagram of one of the filter sections. Adapted from the datasheet. The schematic below is my reverse-engineered schematic of the filter, as implemented on the chip. It closely matches the block diagram, but fills in the details. In the block diagram, the summing circuit (circle) adds one signal and subtracts two signals. This summing circuit is implemented with the three switched capacitors on the left, which act as summing resistors. Note that one switch is grounded during phase 1, while the others are grounded during phase 2; switching the polarity implements addition versus subtraction. The top sum input is either feedback from the low-pass output or ground, selected by an input pin. A CMOS switch is used here, but the switch is static, not clocked, so it doesn't use protection rings and shielding like the other switches. My reverse-engineered schematic of one of the filters. Click this image (or any other) for a larger version. The integrators have switched capacitors on the inputs, acting as resistors. The integration capacitor is either 8 or 16 "squares" of capacitance, selected by a ratio selection pin. This controls the ratio between the clock frequency and the filter frequency, either 50:1 or 100:1.7 Although the integration capacitors are attached to a CMOS switch, the switch is static, so the capacitors act as regular capacitors, not switched capacitors. The op-amps The op-amps are fairly standard CMOS op-amps, built from about 35 transistors. (You might get a lower count if you try counting the transistors below, since some of the blocks are multiple transistors.) The op-amp transistors are much larger than the CMOS switch transistors (very bottom, center). On the die, each op-amp is split into two parts: the differential amplifier on the left and an additional amplification stage on the right. A large capacitor (pinkish) sits between the halves. My first thought was that this was the integration capacitor, but it is just a frequency compensation capacitor, common in many op-amps to stabilize the output. The op-amps also have large transistors next to the output pins; these transistors are functionally part of the op-amps, but located next to the pins to minimize resistance. One of the chip's op-amps. I removed the metal layer to make the transistors visible. One unusual feature of the op-amps is a low-power mode. Pulling a particular IC pin low causes the chip to stop filtering and enter a low-power mode, reducing power consumption by 70%. This is implemented by shutting down the "current mirror" circuits that provide fixed currents to the op-amps and other parts of the chip. The non-overlapping clock generator The MF10 chip is driven by external clock signals, one for each filter, with the frequency of the filter proportional to the clock frequency. The photo of the CMOS switches earlier showed that the clock drives four control lines for the switches. You might think that two control lines would be sufficient: the clock and the inverted clock. The problem is that it is very important to avoid having both switches closed at the same time, even for a moment, as that will short the inputs and corrupt the signals. Instead, the two switches have separate control lines that enforce a small gap between when one switch opens and the other one closes. This is implemented with the circuit below that takes an input clock signal and produces the four outputs that drive the switches. The circuit to generate non-overlapping clock signals. There is a delay between when gate A or B turns on and when the corresponding output changes. The idea behind the circuit is that a phase is blocked from going high until after the other phase goes low, with a pair of inverters providing additional delay. In more detail, suppose the input clock drops from high to low. Gate A will turn off, causing the phase 1 output (ϕ1) to drop after a few gate delays (A delay). Gate B can't turn on until ϕ1 goes low. After additional gate delays, ϕ2 goes high. The behavior is similar when the input clock goes high. Gate B turns off, causing ϕ2 to go low after a delay. This allows gate A to turn on, turning on ϕ1 after more delay. To summarize, after a phase is turned off, there is a delay before the other phase turns on, so the two phases never overlap. The clock-shaping circuitry is implemented with CMOS logic gates. The photo above shows this circuitry under the microscope, with the metal layer removed. The rectangular blocks are doped silicon that forms transistors. The darker regions on the left are NMOS transistors and the lighter regions on the right are PMOS transistors. A CMOS gate consists of NMOS and PMOS transistors working together. The PMOS transistors are larger because PMOS transistors are slightly less efficient than NMOS transistors. The dark circles are contacts between the silicon and the metal layer on top. The copper-colored lines are not metal but a special type of silicon called polysilicon. When a polysilicon line crosses doped silicon, it forms the gate of a transistor. The pinks and greens are due to thin-film interference from a thin layer of oxide that didn't completely dissolve; the silicon is actually gray. The ternary input A weird feature of the chip is the input pin that selects the ratio between the input clock and the filter frequency. In effect, this is a digital input with three values. Tying the pin to the high supply voltage selects a 50:1 ratio. Tying the pin to the midpoint between the supply voltages selects a 100:1 ratio. Pulling the pin to the low supply voltage stops the filter and puts the chip into a low-power mode.8 To handle the three-level input, the input goes through two separate buffers, one that transitions at a lower voltage and one that transitions at a higher voltage. Thus, the two buffers separate the middle signal level. Each buffer consists of a special inverter feeding into a regular inverter. Before explaining the special inverters, I'll review how a regular CMOS inverter works. A CMOS inverter is constructed from a PMOS transistor and an NMOS transistor. When the input is high, the NMOS transistor turns on and pulls the output to ground. When the input is low, the PMOS transistor turns on and pulls the output high. Thus, the input signal is inverted. A CMOS inverter is constructed from a PMOS transistor and an NMOS transistor. In the die photo, you can see the four PMOS transistors (light gray) and four NMOS transistors (darker), forming four inverters. When a polysilicon line (copper-colored) crosses a doped silicon region, it forms the gate of a transistor. For this picture, I dissolved the metal layer in acid so the transistors are visible. The metal layer connected the transistors to complete the wiring of the inverters: it connects the two "out1" contacts to "in2" and connects the two "out2" contacts to the rest of the chip. For the second buffer, "out3" connects to "in4" and so forth. The four inverters that handle the ternary input. I flipped the image to make the orientation better. In this circuit, the length of the transistor gates is varied to make the inverters activate at different voltage levels. Six of the transistor gates are normal (orange arrows); the PMOS gates are wider (in the vertical direction) than the NMOS gates because PMOS transistors are inherently weaker. However, two of the transistor gates are unusually long (horizontal direction, red), making the transistors weak since the current must travel a longer distance. The inverter on the left has a weak PMOS transistor. If the input is high or low, the inverter will operate normally. But if the input is in the middle, both transistors will partially turn on. Since the PMOS transistor is very weak, the NMOS transistor will "win", pulling the output low. Thus, the leftmost inverter treats a medium-level input as a 1, outputting a 0. The third inverter is the opposite; the NMOS transistor has a long, winding gate, so it is weak. In this case, a medium-level input will partially turn on both transistors, but the PMOS transistor will "win", pulling the output high. To summarize, the two inverters have opposite behavior for a middle-level signal, allowing the three input levels to be distinguished. Since the output from a special inverter may be weak, the output goes to a normal inverter to amplify the signal. Conclusions Like most semiconductor companies, Harris has a complicated history. Harris started way back in 1895 as a printing press company. Harris moved into high technology in the 1950s and 1960s, acquiring various radio and electronics companies. In particular, Harris entered the IC business in 1967, when it acquired Radiation, Inc., renaming it Harris Semiconductor a few years later. (We've encountered some Radiation modules in Apollo systems, but I haven't written about them yet.) Harris got out of the semiconductor business in 1999, spinning off Intersil, which was later acquired by the Japanese semiconductor firm Renesas. In 2019, Harris merged with L3 Technologies to become L3Harris, the eighth-largest defense contractor in the US. As for switched-capacitor filters, they have lost popularity as filtering is now more easily done in the digital domain. Texas Instruments acquired National Semiconductor (and the MF10) in 2011; TI's website shows the MF10 as active but expensive and out of stock, so it's probably no longer being manufactured. State variable filters are still used in the synthesizer world both because of their flexibility and because they provide low-pass, band-pass, and high-pass filters in one unit. For more, follow me on Bluesky (@righto.com), Mastodon (@[email protected]), or RSS. Thanks to CuriousMarc for providing the IC. AI statement: Despite the presence of the em dash, no AI was used in the writing of this article (details). Notes and references Once we found the "HF-10" part number, a search turned up a National Semiconductor databook that confirmed that the Harris HF-10 was a direct replacement for the National Semiconductor MF10. It remains a mystery why the Harris chip is externally labeled "F1-10-5" rather than "HF-10". This format doesn't resemble other Harris part numbers. I would suspect a military part number, but it is completely different from the military formats that I've seen on other chips, such as JM38510 numbers or NSN numbers. ↩ You might wonder why the larger capacitors are formed by connecting eight smaller capacitor squares, rather than making one capacitor that is eight times as big. The reason is to get better matching between the two capacitor sizes. A capacitor that is eight times as large won't have exactly eight times the capacitance due to factors such as the behavior of the electric field around the edge of the capacitor, inaccuracies that may make the capacitor slightly larger or smaller than desired, or etching variability around the edges. By building larger capacitors out of identical smaller capacitors, the values can match very well, up to ±0.01% according to The Art of Analog Layout. (With laser trimming, matching of ±0.001% is possible, but that is much more accuracy than the MF10 required.) ↩ Most chips from this era have a single layer of polysilicon, so I was surprised to find two layers in this chip. I've seen two layers of polysilicon before, in the MK4116 DRAM chip and AMD's LANCE Ethernet chip. In both cases, the second layer of polysilicon was used for storage devices. ↩ A standard op-amp integrator is an inverting integrator, and the output is negative. However, the MF10 uses the four-switch switched capacitor that inverts the input voltage. The two negatives cancel out, so the MF-10's integrator is a non-inverting integrator. See Introducing the MF10: A Versatile Monolithic Active Filter Building Block for details. ↩ To remove the metal layer, I used Whink rust stain remover (1.5-3.5% HF) to remove the oxide layer and hydrochloric acid to dissolve the metal. I applied Whink for 20 minutes and HCl for 16 minutes in total. I alternated each chemical for about 3 minutes each, applying a few drops at a time. I examined the die under the microscope after each application to gauge the progress. I stopped at this point since the metal was removed and the underlying transistors were visible. Moreover, the silicon became differentially stained, with NMOS transistors significantly darker than PMOS transistors. Some more Whink would probably improve the appearance of the die, but the risk is that the polysilicon might get removed, which would be bad for reverse engineering. In other words, I'd rather stop too early than destroy the features that I want to see. ↩ For reference, the full block diagram of the chip is below, from the datasheet. Block diagram of the MF10 from the Texas Instruments datasheet.  ↩ The filter frequency of the MF10 can be set to either the clock frequency divided by 50 or divided by 100. You might wonder where these ratios come from, since the capacitors on the chip are in 8:1 or 16:1 ratios, not 50:1 or 100:1. The formula for a switched-capacitor integrator is that the filter frequency is the clock frequency divided by 2π times the capacitor ratio. (This can be derived from the op-amp integrator formula and the equivalent resistance of a switched capacitor.) It turns out 2π×8 is 50.27 and 2π×16 is 100.5, providing the 50 and 100 values. Note that these values aren't exactly 50 and 100; they are off by 0.5%. Curiously, the datasheet specifies that the typical frequency error is ±0.2%, significantly smaller. I suspect that the explanation is that the capacitor ratio is not precisely 16:1, due to stray capacitance in the wiring and other factors, and the designers ensured that these factors tweaked the ratio in the desired direction. ↩ I suspect that the ternary input pin was used because the chip didn't have enough physical pins for all the functions they wanted. Note that the two filters are entirely independent, even with separate clocks, except for the 50/100 ratio control and the A/B mode control. I'm sure that these two functions would have independent control pins if the chip had pins available. They could have used a standard 24-pin package for the chip rather than the somewhat unusual 20-pin package, but maybe they had a motivation for avoiding a much larger 24-pin package. ↩

There was a time I'd look at a board like the Radxa Dragon Q8B (at left, above) and be like, "there's no way I'd spend $209 on an SBC with 8 gigs of RAM". But we're in 2026, and seeing the 8 gig Raspberry Pi 5 going for almost the same amount, I figured I'd give it a shot. On paper, the Q8B beats the Pi 5 in pretty much every way. A lot of that is thanks to this Snapdragon 8cx Gen 3 chip, which is the same chip I tested on Microsoft's Windows Dev Kit 2023.

Reflections on October 7th

The Sting belongs in the pantheon of films I'm deeply embarrassed to have not watched earlier. Not just because it's a great film — and it is — but because it is so incredibly my shit that I feel retroactively spurned for not having watched it sooner.